Lesson 1  Lesson 2  Lesson 3  Lesson 4  Lesson 5  Lesson 6  Lesson 7  Lesson 8  Lesson 9  Lesson 10

Electromechanics |Электромеханика

LESSON 1

Read the text:                                 ELECTRICAL MACHINES

Electric machine is that converts electrical energy into mechanical energy. When an electric current is passed through a wire loop that is in a magnetic field, the loop will rotate and the rotating motion is transmitted to a shaft, providing useful mechanical work. The traditional electric motor consists of a conducting loop that is mounted on a rotatable shaft. Current fed in by carbon blocks, called brushes, enters the loop through two slip rings. The magnetic field around the loop, supplied by an iron core field magnet, causes the loop to turn when current is flowing through it. In an alternating current (AC) motor, the current flowing in the loop is synchronized to reverse direction at the moment when the plane of the loop is perpendicular to the magnetic field and there is no magnetic force exerted on the loop. Because the momentum of the loop carries it around until the current is again supplied, continuous motion results. In alternating current induction motors the current passing through the loop does not come from an external source but is induced as the loop passes through the magnetic field. In a direct current (DC) motor, a device known as a split ring commutator switches the direction of the current each half rotation to maintain the same direction of motion of the shaft. In any motor the stationary parts constitute the stator, and the assembly carrying the loops is called the rotor, or armature. As it is easy to control the speed of direct-current motors by varying the field or armature voltage, these are used where speed control is necessary. The speed of AC induction motors is set roughly by the motor construction and the frequency of the current; a mechanical transmission must therefore be used to change speed. In addition, each different design fits only one application. However, AC induction motors are cheaper and simpler than DC motors. To obtain greater flexibility, the rotor circuit can be connected to various external control circuits. Most home appliances with small motors have a universal motor that runs on either DC or AC. Where the expense is warranted, the speed of AC motors is controlled by employing special equipment that varies the power-line frequency, which in the United States is 60 hertz (Hz), or 60 cycles per second. Brushless DC motors are constructed in a reverse fashion from the traditional form. The rotor contains a permanent magnet and the stator has the conducting coil of wire. By the elimination of brushes, these motors offer reduced maintenance, no spark hazard, and better speed control. They are widely used in computer disk drives, tape recorders, CD drives, and other electronic devices. Synchronous motors turn at a speed exactly proportional to the frequency. The largest motors are synchronous motors with DC passing through the rotor.

Generator in electricity is a machine used to change mechanical energy into electrical energy. It operates on the principle of electromagnetic induction, discovered by Michael Faraday. When a conductor passes through a magnetic field, a voltage is induced across the ends of the conductor. The generator is simply a mechanical arrangement for moving the conductor and leading the current produced by the voltage to an external circuit, where it actuates devices that require electricity. In the simplest form of generator the conductor is an open coil of wire rotating between the poles of a permanent magnet. During a single rotation, one side of the coil passes through the magnetic field first in one direction and then in the other, so that the induced current is alternating current , moving first in one direction, then in the other. Each end of the coil is attached to a separate metal slip ring that rotates with the coil. Brushes that rest on the slip rings are attached to the external circuit. Thus the current flows from the coil to the slip rings, then through the brushes to the external circuit. In order to obtain direct current, i.e., current that flows in only one direction, a commutator is used in place of slip rings. The commutator is a single slip ring split into left and right halves that are insulated from each other and are attached to opposite ends of the coil. It allows current to leave the generator through the brushes in only one direction. This current pulsates, going from no flow to maximum flow and back again to no flow. A practical DC generator, with many coils and with many segments in the commutator, gives a steadier current. There are also several magnets in a practical generator. In any generator, the whole assembly carrying the coils is called the armature, or rotor, while the stationary parts constitute the stator. Except in the case of the magneto, which uses permanent magnets, AC and DC generators use electromagnets. Field current for the electromagnets is most often DC from an external source. The term dynamo is often used for the DC generator; the generator in automotive applications is usually a dynamo. An AC generator is called an alternator. To ease various construction problems, alternators have a stationary armature and rotating electromagnets. Most alternators produce a polyphase AC, a complex type of current that provides a smoother power flow than does simple AC. By far the greatest amount of electricity for industrial and civilian use comes from large AC generators driven by steam turbines.

1.Match  the left part with the right:

2. Complete the sentences with the suggested words:

called   have   is   used

 The term dynamo is often (1)______ for the DC generator; the generator in automotive applications (2)______ usually a dynamo. An AC generator is (3)______ an alternator. To ease various construction problems, alternators (4)______ a stationary armature and rotating electromagnets.